Properties of Fresh Concrete and Factors Affecting Properties

Properties of concrete are divide into two major groups

• Properties of Fresh Concrete

• Properties of Hardened Concrete

Fresh Concrete

Fresh concrete is that stage of concrete in which concrete can be moulded and it is in plastic state. This is also called "Green Concrete". Another term used to describe the state of fresh concrete is consistence, which is the ease with which concrete will flow.

Operations on Fresh Concrete

Batching, mixing, transporting, placing, compacting, surface finishing.

Main properties of fresh concrete during mixing, transporting, placing and compacting

Fluidity or consistency:

capability of being handled and of flowing into formwork and around any reinforcement, with assistance of compacting equipment

Compactability:

Air entrapped during mixing and handling should be easily removed by compaction equipment, such as poker vibrators

Stability or cohesiveness:

fresh concrete should remain homogenous and uniform. No segregation of cement paste from aggregates (especially coarse ones)

Fluidity & compactability known as workability

Higher workability concretes are easier to place and handle but obtaining higher workability by increasing water content decreases strength and durability

Properties of Concrete

Following are the important properties of fresh concrete

1. Setting

2. Workability

3. Bleeding and Segregation

   1. Bleeding

   2. Segregation

4. Hydration

5. Air Entrainment

1. Setting of Concrete

The hardening of concrete before its hydration is known as setting of concrete. OR

The hardening of concrete before it gains strength. OR

The transition process of changing of concrete from plastic state to hardened state. Setting of concrete is based or related to the setting of cement paste. Thus cement properties greatly affect the setting time.

Factors affecting setting:

Following are the factors that affect the setting of concrete.

1. Water Cement ratio
2. Suitable Temperature
3. Cement content
4. Type of Cement
5. Fineness of Cement
6. Relative Humidity
7. Admixtures
8. Type and amount of Aggregate

2. Workability of Concrete

Workability is often referred to as the ease with which a concrete can be transported, placed and consolidated without excessive bleeding or segregation.

OR

The internal work done required to overcome the frictional forces between concrete ingredients for full compaction. It is obvious that no single test can evaluate all these factors. In fact, most of these cannot be easily assessed even though some standard tests have been established to evaluate them under specific conditions. In the case of concrete, consistence is sometimes taken to mean the degree of wetness; within limits, wet concretes are more workable than dry concrete, but concrete of same consistence may vary in workability.

Because the strength of concrete is adversely and significantly affected by the presence of voids in the compacted mass, it is vital to achieve a maximum possible density. This requires sufficient workability for virtually full compaction to be possible using a reasonable amount of work under the given conditions. Presence of voids in concrete reduces the density and greatly reduces the strength: 5% of voids can lower the strength by as much as 30%. Slump Test can be used to find out the workability of concrete. View Procedure of Slump Test

Factors affecting concrete workability:

1. Water-Cement ratio
2. Amount and type of Aggregate
3. Amount and type of Cement
4. Weather conditions
   1. Temperature
   2. Wind
5. Chemical Admixtures
6. Sand to Aggregate ratio

3(a). Concrete Bleeding

Bleeding in concrete is sometimes referred as water gain. It is a particular form of segregation, in which some of the water from the concrete comes out to the surface of the concrete, being of the lowest specific gravity among all the ingredients of concrete. Bleeding is predominantly observed in a highly wet mix, badly proportioned and insufficiently mixed concrete. In thin members like roof slab or road slabs and when concrete is placed in sunny weather show excessive bleeding. Due to bleeding, water comes up and accumulates at the surface. Sometimes, along with this water, certain quantity of cement also comes to the surface. When the surface is worked up with the trowel, the aggregate goes down and the cement and water come up to the top surface. This formation of cement paste at the surface is known as “Laitance”. In such a case, the top surface of slabs and pavements will not have good wearing quality. This laitance formed on roads produces dust in summer and mud in rainy season.

Water while traversing from bottom to top, makes continuous channels. If the water cement ratio used is more than 0.7, the bleeding channels will remain continuous and un segmented. These continuous bleeding channels are often responsible for causing permeability of the concrete structures. While the mixing water is in the process of coming up, it may be intercepted by aggregates. The bleeding water is likely to accumulate below the aggregate. This accumulation of water creates water voids and reduces the bond between the aggregates and the paste. The above aspect is more pronounced in the case of flaky aggregate. Similarly, the water that accumulates below the reinforcing bars reduces the bond between the reinforcement and the concrete. The poor bond between the aggregate and the paste or the reinforcement and the paste due to bleeding can be remedied by re vibration of concrete. The formation of laitance and the consequent bad effect can be reduced by delayed finishing operations. Bleeding rate increases with time up to about one hour or so and thereafter the rate decreases but continues more or less till the final setting time of cement.

Prevention of Bleeding in concrete

• Bleeding can be reduced by proper proportioning and uniform and complete mixing.

• Use of finely divided pozzolanic materials reduces bleeding by creating a longer path for the water to traverse.

• Air-entraining agent is very effective in reducing the bleeding.

• Bleeding can be reduced by the use of finer cement or cement with low alkali content. Rich mixes are less susceptible to bleeding than lean mixes.

The bleeding is not completely harmful if the rate of evaporation of water from the surface is equal to the rate of bleeding. Removal of water, after it had played its role in providing workability, from the body of concrete by way of bleeding will do good to the concrete. Early bleeding when the concrete mass is fully plastic, may not cause much harm, because concrete being in a fully plastic condition at that stage, will get subsided and compacted. It is the delayed bleeding, when the concrete has lost its plasticity, which causes undue harm to the concrete. Controlled re vibration may be adopted to overcome the bad effect of bleeding.

3(b). Segregation in concrete

Segregation can be defined as the separation of the constituent materials of concrete. A good concrete is one in which all the ingredients are properly distributed to make a homogeneous mixture. There are considerable differences in the sizes and specific gravities of the constituent ingredients of concrete. Therefore, it is natural that the materials show a tendency to fall apart.

Segregation may be of three types

1. Coarse aggregate separating out or settling down from the rest of the matrix.
2. Paste separating away from coarse aggregate.
3. Water separating out from the rest of the material being a material of lowest specific gravity.

A well made concrete, taking into consideration various parameters such as grading, size, shape and surface texture of aggregate with optimum quantity of waters makes a cohesive mix. Such concrete will not exhibit any tendency for segregation. The cohesive and fatty characteristics of matrix do not allow the aggregate to fall apart, at the same time; the matrix itself is sufficiently contained by the aggregate. Similarly, water also does not find it easy to move out freely from the rest of the ingredients.

The conditions favorable for segregation are:

1. Badly proportioned mix where sufficient matrix is not there to bind and contain the aggregates
2. Insufficiently mixed concrete with excess water content
3. Dropping of concrete from heights as in the case of placing concrete in column concreting
4. When concrete is discharged from a badly designed mixer, or from a mixer with worn out blades
5. Conveyance of concrete by conveyor belts, wheel barrow, long distance haul by dumper, long lift by skip and hoist are the other situations promoting segregation of concrete

Vibration of concrete is one of the important methods of compaction. It should be remembered that only comparatively dry mix should be vibrated. It too wet a mix is excessively vibrated; it is likely that the concrete gets segregated. It should also be remembered that vibration is continued just for required time for optimum results. If the vibration is continued for a long time, particularly, in too wet a mix, it is likely to result in segregation of concrete due to settlement of coarse aggregate in matrix.

4. Hydration in concrete

Concrete derives its strength by the hydration of cement particles. The hydration of cement is not a momentary action but a process continuing for long time. Of course, the rate of hydration is fast to start with, but continues over a very long time at a decreasing rate In the field and in actual work, even a higher water/cement ratio is used, since the concrete is open to atmosphere, the water used in the concrete evaporates and the water available in the concrete will not be sufficient for effective hydration to take place particularly in the top layer.

If the hydration is to continue, extra water must be added to refill the loss of water on account of absorption and evaporation. Therefore, the curing can be considered as creation of a favorable environment during the early period for uninterrupted hydration. The desirable conditions are, a suitable temperature and ample moisture. Concrete, while hydrating, releases high heat of hydration. This heat is harmful from the point of view of volume stability. Jeat of hydration of concrete may also shrinkage in concrete, thus producing cracks. If the heat generated is removed by some means, the adverse effect due to the generation of heat can be reduced. This can be done by a thorough water curing.

5. Air Entrainment

Air entrainment reduces the density of concrete and consequently reduces the strength. Air entrainment is used to produce a number of effects in both the plastic and the hardened concrete. These include:

1. Resistance to freeze–thaw action in the hardened concrete.
2. Increased cohesion, reducing the tendency to bleed and segregation in the plastic concrete.
3. Compaction of low workability mixes including semi-dry concrete.
4. Stability of extruded concrete.
5. Cohesion and handling properties in bedding mortars.

Properties of Concrete Video